Built into the wall, not bolted on. The Surefix Rise & Fall Built‑In Bracket is mortared into the bed joint as the wall goes up. Precision‑engineered embedment holes allow the mortar to flow through the stake and cure around it, creating a true mechanical bond . A long external slot remains visible, giving installers full rise‑and‑fall and in‑out adjustment after construction . Something the current bracket lacks.
Same performance, different timing. This bracket comes from the same precision‑engineered family as the screw‑in adjustable version; both offer identical adjustment range and strength—the only difference is when you fit them . By installing the built‑in bracket during bricklaying, you achieve structural‑level anchorage, perfect alignment and a clean façade with no alteration needed later .
Ideal for any façade. The built‑in design suits stone, brick, block or mixed façades because you’re securing the bracket within the build, not into the surface . It’s the perfect choice for developers, housebuilders, self‑builders and architects who want a permanent, precise fixing from day one.
At the heart of the Surefix built-in system are two defining design features:
These circular holes sit inside the mortar joint.
When the stake is placed into wet mortar, the mix flows through these holes and cures around them. This creates a true mechanical bond, locking the stake inside the wall. It doesn’t rely on pressure, friction or guesswork — the stake becomes part of the structure.
This is the part that remains outside the wall once built.
The long slot is what makes this bracket different from traditional built-in stakes. It gives the installer two critical adjustments:
Move the gutter bracket closer to or farther from the wall to achieve a perfect line.
Adjust up or down without repositioning or modifying the built-in stake.
Traditional hammer-in, built-in brackets offer neither of these control elements. They sit where they land.
The Surefix built-in version gives installers freedom, accuracy and confidence — even years after the stake was installed.
Choosing a built-in bracket means planning for accuracy from day one. When the fixing point becomes part of the brickwork, everything that follows becomes easier, cleaner and more predictable.
Because the embedment holes pull mortar through the steel, the cured bond is incredibly secure. The stake doesn’t twist, loosen or rock over time.
No drilling into hard stone.
No crumbling mortar.
No unexpected voids behind the wall.
The bracket is secured within the build, not onto the surface.
Your finished façade stays intact, with no drill holes, no plugs, and no later patching.
Built-in stakes ensure every fixing point is placed at the same course height, giving long rows of homes consistent gutter lines from the very first install.
In many parts of the industry, installers still attempt to hammer rise-and-fall stakes into dry mortar after the wall is complete. This approach provides:
Dry mortar cannot “grab” steel. The stake may sit temporarily, but over time it can shift, lean forward or come loose entirely.
The Surefix built-in bracket avoids these risks completely.
It uses wet mortar, engineered embedment holes and structural bonding to make the stake part of the building. Nothing is hammered in. Nothing depends on friction. Everything is planned and secure.
Lay the mortar bed as normal
The joint is prepared according to specification, ready for the stake.
The Surefix built-in stake is placed along the bed joint.
The embedment holes must sit fully inside the mortar so the mix can flow through and set around them.
Set the projection and align with the future gutterline.
The bricklayer ensures the part of the stake protruding from the wall is roughly at the correct projection for the future gutterline.
But unlike traditional built-in stakes, the long external slot gives installers complete flexibility later. Even if the projection is slightly off, the gutter bracket can be adjusted in or out, and up or down, without altering the stake.
The stake fixes the position.
The long slot gives freedom.
The installer gets perfect control every time.
Lay the next course and lock the stake in place.
As bricks or blocks are placed above, the mortar flows through the embedment holes and cures into a hardened interlock — turning the stake into a structural anchor.
Fit the gutter bracket and set the fall
Both brackets offer the same dependable rise-and-fall control, full in–out adjustment, strength in challenging conditions, compatibility with the Surefix gutter cups, reliable alignment and long-term performance; the built-in version is simply optimised for new builds and projects at the bricklaying stage, while the screw-in adjustable bracket is the correct choice when the wall is already finished.
This bracket uses the same principles as the Surefix Adjustable Rise & Fall Gutter Bracket (the screw-in version). The difference is simply when and how it is fixed.
Both brackets offer:
The built-in version is simply the version optimised for new builds and projects at the bricklaying stage.
If the wall is already finished, the screw-in adjustable bracket is the correct choice.
Many built-in brackets on the market still use a simple flat bar hammered into dry mortar. The Surefix built-in bracket moves the entire industry forward.
Its uniqueness comes from two engineered design decisions:
1. The embedment holes
They sit fully inside the mortar joint, creating a genuine mechanical lock when the mortar cures.
2. The long external slot
It remains visible after construction and gives installers full freedom to fine-tune the brackets:
This means the bricklayer only needs to get the projection reasonably close.
The installer finishes the precision work later with no compromise.
That combination — structural embedment + full adjustability — is what sets this bracket apart.
By the time the mortar has cured, the built-in stake is bonded, locked and immovable. It does not twist, slip or ease forward under gutter weight or wind load, which means you achieve a stronger fixing, a cleaner elevation, a more accurate gutterline, and a bracket that remains in the same position decades later.
Developers appreciate the consistency this delivers across plots, installers value the ease and accuracy at final fix, and homeowners benefit from a finished appearance that simply looks right.
The Surefix Rise & Fall Built-In Gutter Bracket provides a structural anchor that becomes part of the wall while still offering full adjustment through the external slot, giving installers precise control during the final fit.
It is simple to install, clean on elevation and engineered to last, making it the ideal choice for any project still at the bricklaying stage.
The Surefix Rise & Fall Built-In Gutter Bracket is a gutter fixing system designed to be installed during bricklaying rather than after the wall is built. The stake includes precision-engineered embedment holes that sit within the mortar joint. As the mortar cures, it bonds through these holes, locking the bracket securely into the structure. A long external slot remains outside the wall to allow installers to make in–out adjustments and control rise-and-fall height when fitting the gutter.
Choose the built-in version when the project is still at the bricklaying stage, and you want the fixing to become part of the wall. It delivers structural-level stability, a clean façade with no drilling and guaranteed consistency across long elevations. The screw-in adjustable version is the correct choice for after-build installations or retrofitting. Both offer the same adjustment features, but they are used at different moments in the build.
The bracket is engineered with internal embedment holes that allow wet mortar to flow through and harden around them. This creates a mechanical lock within the joint, preventing the stake from twisting, pulling forward or loosening over time. It is far more reliable than traditional hammer-in methods, which rely only on friction and have no true bonding.
Yes. Even though the stake is fixed inside the wall, the installer can adjust the gutterline easily using the long external slot. This slot allows fine control of projection (moving the gutter closer or further from the wall) as well as rise-and-fall height adjustments. The bricklayer sets the approximate projection during build, and the installer perfects the final alignment later.
The Surefix built-in bracket works with both Surefix gutter cups — the 100mm half-round cup and the 125mm deep-flow version — allowing it to support uPVC, aluminium, steel, cast iron, and powder-coated systems. Its structural stability and full adjustability make it suitable for domestic builds, commercial projects, stone façades, blockwork, and mixed-material elevations.
Fill out the form below, and we will be in touch shortly to run though your order. No card details will be asked for via this form.